RFS Hydraulics

Swagelok

Plumbing & Sanitary

plumbing-sanitary

Pipe Adaptor

pipe-adaptor

Pipe Coupling

pipe-coupling

Cleaning Process	Standard Cleaning and Packaging (SC-10)

Connection 1 Type	Swagelok® Tube Fitting

Connection 2 Type	Male ISO Parallel Thread, Straight Shoulder

<h3 class="md-block-header-three">Swagelok SS-10M0-1-4RS Connector</h3>Body Material	316 Stainless SteelBored Through	NoCleaning Process	Standard Cleaning and Packaging (SC-10)Connection 1 Size	10 mmConnection 1 Type	Swagelok® Tube FittingConnection 2 Size	1/4 in.Connection 2 Type	Male ISO Parallel Thread, Straight ShoulderFlow Restrictor	No

<h3>Swagelok SS-10M0-1-4RS Connector</h3>
Body Material	316 Stainless Steel
Bored Through	No
Cleaning Process	Standard Cleaning and Packaging (SC-10)
Connection 1 Size	10 mm
Connection 1 Type	Swagelok® Tube Fitting
Connection 2 Size	1/4 in.
Connection 2 Type	Male ISO Parallel Thread, Straight Shoulder
Flow Restrictor	No

WEICON

Nietz

Pilot

Picasaf

Fellowes

DEVCON

Philips

BELZONA

Whatman

Writing Materials

Adhesive Glue

Epoxy

Degreasers

Threadlocker

Anti Rust Coating & Lubricant

Lubricants

Combination Spanners

Other Tools

Sealants

Darius Ong 

Swagelok SS-10M0-1-4RS Connector

swagelok ss-10m0-1-4rs connector konektor pipe adaptor pipa penyambung penyesuai paip swagelok/世伟洛克 连接器 世伟洛克

swagelok-ss-10m0-1-4rs-connector

Rfs Brass 10mm Od X 10mm Od Union Coupling Compression Fittings, Light Series F-D-B-U-10L

Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation.  To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule union coupling helps to attach and detach pipes without leaving deformities. It has three parts which are the male end, sleeve and nut. 

Series	: L (Light Series) & S (Heavy Series)

Working Pressure (bar)	: L series (160-315) & S series (315-800)

Material Standard	: DIN 2353 / DIN EN 3851 / ISO 8434-1

Step 1: Cutting ring and nut to be placed over the tube in the correct direction.

Step 2: Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.

Step 3: Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.

Step 4: Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.

Step 5: With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3 class="md-block-header-three">Rfs Brass 10mm Od X 10mm Od Union Coupling Compression Fittings, Light Series F-D-B-U-10L</h3>Union CouplingCompression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule union coupling helps to attach and detach pipes without leaving deformities. It has three parts which are the male end, sleeve and nut. About Union CouplingSize	: 6mm to 42mmSeries	: L (Light Series) &amp; S (Heavy Series)Working Pressure (bar)	: L series (160-315) &amp; S series (315-800)Material	: BrassMaterial Standard	: DIN 2353 / DIN EN 3851 / ISO 8434-1DIN Fittings installation guidelines:Step 1: Cutting ring and nut to be placed over the tube in the correct direction.Step 2: Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.Step 3: Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.Step 4: Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.Step 5: With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

<h3>Rfs Brass 10mm Od X 10mm Od Union Coupling Compression Fittings, Light Series F-D-B-U-10L</h3>
Union Coupling
Compression fittings are commonly used in applications that requires excellent sealing in high temperature and pressure setting. These fittings are also known as single ferrule. They have a simpler design than double ferrules. Compression fittings are made to DIN 2353, ISO 8434-1, and DIN EN 3851 standards. These fittings are available in 3 series; S, L, and LL. Each series is made to suit different pressure needs. S series (high pressure) fitting has a working pressure of 315 to 630 bars, while L series (light pressure) fitting has a working pressure between 160 to 315 bars. The lowest pressure (LL) series is 100 bars. Compression fittings can be assembled and reassembled many times. Fittings vary in design but they are all made up of three parts; Body, nut, and sleeve. The benefits offered by compression fitting are fewer leak paths, dampens vibration, flexibility, and ease of installation. To install a compression fitting, place the ring and nut over the tube. Then, use a pre-assembly tool and insert the tube up to tube abutment and tighten it with 1 1/4 turns. Remove the pre-assembly tool and untighten it. Remove the nut to see if there is any visible ring formed over the tube. Use a wrench to tighten the nut with the fitting body in an upward position until there is a noticeable feeling in increase of torque and further tighten the nut ¼ turn. Single ferrule union coupling helps to attach and detach pipes without leaving deformities. It has three parts which are the male end, sleeve and nut.&nbsp;
About Union Coupling
Size	: 6mm to 42mm
Series	: L (Light Series) &amp; S (Heavy Series)
Working Pressure (bar)	: L series (160-315) &amp; S series (315-800)
Material	: Brass
Material Standard	: DIN 2353 / DIN EN 3851 / ISO 8434-1
DIN Fittings installation guidelines:
Step 1: Cutting ring and nut to be placed over the tube in the correct direction.
Step 2: Insert tube into pre-assembly tool up to tube abutment and tighten with the nut.
Step 3: Tighten 1 ¼ turns beyond the hand tighten position by using a wrench.
Step 4: Take out the pre-assembly and untighten and remove the nut to check the ring formed up over the tube. The visible ring is formed up with the penetration of the cutting ring into the tube surface.
Step 5: With fitting body holding up, use a wrench to tighten the nut until a noticeable increase in torque in felt. Beyond this point tighten the nut ¼ turn for last round of assembly.

AF Hydro

Oleo Tecnica

Others

BOTHWELL

LAME

Stauff

Flanges

Hydraulic Tools

Pipe Clamps

Hose Clamp

Stainless Steel Tubes

Ferrule Fittings

Pipe Elbow

Pipe Nipple

Kelvin How

buyerIntroduction

Rfs Brass 10mm Od X 10mm Od Union Coupling Compression Fittings, Light Series

rfs brass 10mm od union coupling compression fittings, light series seri ringan f-d-b-u-10l pipe kopling pipa hydraulics loyang kelengkapan mampatan gandingan kesatuan, siri paip hydraulics/rfs 液压 黄铜 联管接头压缩接头，轻型系列